(602) 858-6800
Our Products
(602) 858-6800Request a Quote
Macho Supply|Scottsdale, AZ 85255|(602) 858-6800

Who We Are

We're proud to partner with wastewater manufacturers like E/One and Tuf-Tite, as well as local provider & wastewater designers, James, Cooke & Hobson (JCH).

Lift Stations

Learn More

Septic Systems

Learn More

Additional Product Information

EQD INSERT FEMALE 6-PIN

SKU:
PA1074P03

Description:
Female Electronic Quick Disconnect Insert

EQD HOUSING

SKU:
ND0058G01

Description:
EQD Housing/Hoods

E/ONE EXTREME SERIES GRINDER PUMP

SKU:
D200A01A01AA

Description:
The grinder pump turns on and off automatically and runs for very short periods several times per day. Electrical consumption is low — a household that uses 250 gallons of water per day should use between 6 kwhr and 23 kwhr per month to run the pump. (Actual water and power usage will vary depending on the system pressure.) For a standard 240V single-phase installation, a dedicated 30A breaker is required, with #10 wire, to the E/One panel. You need to bring L1, L2, N and Gnd.

If only 208V power is available, a buck-boost transformer is required to boost 208V to 240V. The E/One pump requires a minimum of 216V to start and run reliably.

D-SERIES | DH071 & DR071 GRINDER PUMP STATION

SKU: DH071/DR071

Description:
Grinder pumps collect wastewater from the home and send it to the central sewer and/or treatment system through small-diameter pipes.

The DH071/DR071 grinder pump station consists of a pump and a tank with a dry accessway. The grinder pump uses integrated level-sensing pressure switches instead of floats — the "core"-style pump is compact and easily removed for service if needed.

The DH071 is the “hardwired,” or “wired,” model where a cable connects the motor controls to the level controls through watertight penetrations.

The DR071 is the “radio frequency identification” (RFID), or “wireless,” model that uses wireless technology to communicate between the level controls and the motor controls.

The tank is made from tough, corrosion-resistant HDPE and provides 70 gallons of capacity. A single DH071/DR071 is ideal for one, average single-family home and can be used for up to two homes where codes allow and with the consent of the factory. The DH071/DR071 can accommodate flows of 700 gallons per day.

Stations are available for indoor and outdoor installations. Outdoor stations accommodate a wide range of depths, suitable for both warm and cold climates (refer to drawings above).

E/One requires the installation of its stainless steel UNI-LATERAL to prevent backflow from the sewer system from entering the grinder pump station.

Inlet Connections: 4" inlet grommet standard for DWV pipe. Other inlet configurations are available from the factory.

Discharge Connections: Pump discharge terminates in 1-1/4" NPT female thread. Can easily be adapted to 1-1/4" PVC pipe or any other material required by local codes.

DISCHARGE:

  • 15 gpm at 0 psig
  • 11 gpm at 40 psig
  • 7.8 gpm at 80 psig

PUMP STATOR 8203

SKU: NC0039G01

Description:
Stator Liner Assembly for Environment One DH071 and DH151 Grinder Pumps

K-200-IRB-4

SKU: K-200-IRB-4

Description:
Intermediate Rail Support (Includes U-Bolts and Fasteners)

MATERIAL: Stainless Steel

USED WITH: KL4

PIPE GUIDE: 2"

K4VP(X)

SKU: K4VP(X)

Description:
4” Submersible, Enclosed Impeller

(Class 1, Div. 1, Groups C & D Hazardous Location)

HEAVY-DUTY PUMP SERIES

  • Handles Aggressive Pumping Applications
  • Strong Pumping Capacities to 1200 GPM
  • Smooth, Quiet Operation
  • Centerline Volute Discharge

STRONG PERFORMANCE

  • Non-overloading Performance Curve
  • Pump-Out Vanes Prevent Material Build-up
  • Positive Pumping Action through Impeller
  • Ideal for Higher Flows

LONG SERVICE LIFE

  • Dual Silicon Carbide Shaft Seals
  • Low Motor Operation Temperatures
  • Continuously Lubricated Ball Bearings

LOW MAINTENANCE

  • Easily Replaceable Impeller Wear Ring Restores
  • Original Pump Performance
  • Unobstructed Impeller Passageway
  • Grit-Resistant Silicon Carbide Shaft Seals
  • Large, 3” diameter Solids-Handling
  • High Service Factor Motor Handles Tough Electrical Operating Conditions

CAPABILITIES:

  • Flows-------------------------------------- to 1200 GPM
  • Heads------------------------------------- to 118 Feet
  • HP Range-------------------------------- 3 - 20 HP
  • Voltage / Phase Options------------- 208/230/460/575V, 3-Phase or 208/230V, 1-Phase
  • Discharge Connections-------------- 4” ANSI Class 125 Horizontal Flange
  • Motor Speeds--------------------------- 1150 / 1750 RPM
  • Solids-Handling------------------------ 3”
  • Impeller---------------------------------- Balanced, Enclosed, 2-Vane
  • Motor Service Factor----------------- 1.20

KL4X

SKU: KL4X

Description:
Lift-Out System

GUIDE PIPE SIZE REQ'D: 2"

DISCH. ELBOW: 4"

USED WITH: 4"Sewage Pumps

NOTE: STAINLESS STEEL TOP RAIL SUPPORT BRACKET INCLUDED WITH LIFT-OUT SYSTEM

RETROFIT (ASSY) PACKAGE EPCG15-21CSL-10-IF

SKU: KERPC-0017

Description:
Retrofit (ASSY) package EPCG15-21CSL-10-IF consists of: EPCG-21CSL pump W/ FLOATS, SST 'Open style' cover, Brass swing check valve, and antisiphon valve, SST gooseneck, on-off and alarm floats (mech), lift out rope, 'Extreme series' eqd, cord grips, discharge grommet and o-ring (Wiring KN-1240) (PER DRAWING KERPC-0017)

Serial# 2208577 - 2208579

RETROFIT (ASSY) PACKAGE RKG15-21C-10-IF

SKU: KER-0003

Description:
Retrofit (ASSY) package RKG15-21C-10-IF consists of: RKG15-21C-10-IF pump, SST 'Open style' cover, Brass swing check valve/anti-siphon, SST gooseneck, on-off and alarm floats (mech), lift out rope, 'Extreme series' eqd, cord grips, discharge grommet and o-ring (Wiring KN-1240) (Dwg KER-0002 Rev.N) Serial# 2207545 - 2207547

6" X 36" DIA BASIN EXTENSION

SKU: KBE-36X6A

Description:
6" x 36" dia Basin Extension

EXTENSION, FIBERGLASS BASIN 36 IN ID X 12 IN DEEP (INCLUDES FASTENERS AND GASKET)

SKU: KBE-36X12A

Description:
EXTENSION, FIBERGLASS BASIN 36 in ID X 12 in DEEP (INCLUDES FASTENERS AND GASKET)

KBPG-36X60LCG22401

SKU: KBPG-36X60LCG22401

Description:
DUPLEX GRINDER PUMP BASIN PACKAGE CONTAINING:

*LCG2-2401 GRINDER PUMP, 2 HP, 240/1/60, 30 ft CORDS

*KL1CV LIFT OUT SYSTEMS W/ INTEGRAL CHECK VALVE, SST UPPER GUIDE BRACKETS, 3/4 in GUIDE RAILS, 5 ft LIFT CHAIN

*1-1/4 in SCHEDULE 80 PVC DISCHARGE PIPING, TRUE UNION BALL VALVE WITH SST HANDLE, 24 in DISCHARGE DEPTH, SST 1-1/4 in DISCH FLANGE

*(2) CONDUIT HUBS, SST 4-HOOK FLOAT BRACKET, AND (4) 30 ft FLOAT SWITCHES *4 in INLET HUB (LOOSE)

*KCG-16-21D DUPLEX CONTROL PANEL *36 in X 60 in FIBERGLASS BASIN, ANTI-FLOTATION PLATE, SOLID FIBERGLASS COVER (PER DRAWING KN-675_35689)

FLOAT TREE - 3

SKU: MDIFT3

Description:
3 Hold Float Tree, Stainless Steel Brackets

FLOAT TREE - 4

SKU: MDIFT4

Description:
Float Tree 4 Hole Stainless Steel Brackets

FLOAT SWITCH WITH GOLD PLATED CONTACTS - 30 FOOT - NORMALLY OPEN - WIDE ANGLE

SKU: GF2OW30F0 G

Description:
These high-quality float switches have gold-plated contacts, commonly used in intrinsically safe applications. The float switch is as normally open or pump down (circuit is complete when the float is elevated).

The float cord is intended to be attached to a vertical pipe, band clamp, cable tie, or tether clamp. As an option, the float can be installed with a cable weight as the pivot point.

This float has skived ends, where the insulated wire leads inside the cable are intended to be wired into other system components inside a junction box.

PUMP DUTY FLOAT SWITCH - 30 FOOT - NORMALLY OPEN - WIDE ANGLE - 120 VAC PIGGYBACK PLUG

SKU: GF2OW30F1

Description:
These high-quality float switches are designed for pump duty loads. The float switch is as normally open or pump down (circuit is complete when the float is elevated).

The float cord is intended to be attached to a vertical pipe, band clamp, cable tie, or tether clamp. As an option, the float can be installed with a cable weight as the pivot point.

This float has a 120 VAC Piggyback Plug, where no junction boxes or complicated electrical connections are needed. Plug the switch into a standard 120 VAC outlet, and plug your pump into the piggyback plug.

24" RISER SYSTEM-- FLAT LID

SKU: 24-RISL-FLAT

Description:
TUF TITE 24-inch Riser Lid Green

24” TUF-TITE flat lid seals to the riser with a molded-in lid gasket to assure a watertight seal every time. The lid is secured with eight stainless steel screws (included). Made for heavy-duty protection & walkover. 24-RISL-GREEN

Stainless Steel Screws Included Molded-in Gasket - no more fighting with O-rings

4" EFFLUENT FILTER

SKU: EF-4

Description:
The EF-4 series filters remove solids down to 1/16" and greatly extend the life of the septic system.

4" EFFLUENT FILTER & 4" T-BAFFLE

SKU: EF-4 Combo

Description:
TUF-TITE Effluent Filter EF-4 Combo Includes filter & housing.

Solids mixed with the effluent entering the septic field can cause catastrophic damage to the entire system. The Ef4 by Tuf Tite removes solids down to 1/16" and greatly extend the life of your septic system. Shown above is the Tuf-Tite EF-4 Combo which includes the 4" standard length (14" rise) T-Baffle, the EF-4 Filter, and the B4035 bushing for reducing the outlet from Sch. 40 to SDR35 pipe.

Up to 800 GPD (gallons per day)

86 ft. of 1/16" Filtration

Tuf-Tite Ef-4 Elluent Filter Combo Does not include Gas/Solids Deflector

ANSI/NSF Standard 46

4" SANITARY AND 4" T-BAFFLE

SKU: TB-4

Description:
Fits 4" TB-4x3 SDR-35 Pipe, Optional 4" TB4x3 Reducer, May also be used as Inlet & Outlet Tee

4" SANITARY/OUTLET T-BAFFLE 18

SKU: TB-4-18

Description:
Combo is same as EF-4 with an 18" rise

6" EFFLUENT FILTER

SKU: EF-6 Filter

Description:
The EF-6 series filters remove solids down to 1/16" and greatly extend the life of the septic system.

6" SANITARY T-BAFFLE

SKU: TB-6 Housing

Description:
Fits 4" TB-4x3 SDR-35 Pipe, Optional 4" TB4x3 Reducer, May also be used as Inlet Tee when Solids Deflector is removed

6" EFFLUENT FILTER & 6" T-BAFFLE

SKU: EF-6 Combo

Description:
Tuf-Tite filters are designed to extend the life of your drainfield by preventing solids from leaving the septic tank. The filter fits into either a 4" or 6" Tee Baffle. The EF-6 Combo includes a standard length (14" rise) Sanitary T-Baffle™, the EF-6 Filter, and the B4035 bushing.

SCH.40 TO SDR-35 BUSHING

SKU: B4035

Description:
Bushing to convert the TB-4 to SDR-35

6-HOLE DISTRIBUTION BOX

SKU: 6HD2

Description:
The 6-hole Distribution Box comes complete with a lid and your choice of 8 fittings: S-35 Seal (yellow), S-85 Plug/Seal (orange)

Request a Quote

Service Area

Serving the Scottsdale, Fountain Hills, Phoenix, Rio Verde, Carefree, Paradise Valley, Mesa, & Cave Creek areas.

Business Hours

Monday8:00AM-5:00PM
Tuesday8:30AM-5:00PM
Wednesday8:30AM-5:00PM
Thursday8:30AM-5:00PM
Friday8:30AM-5:00PM
Saturday9:00AM-1:00PM
Copyright © 2024 Macho Supply, All rights reserved.